Its also got built-in 4-channel crossovers. Each unit also features GUI based input and output level metering along with assignable mute functions that are triggered via an audio signal or contact closure. The 4-channel GM-6300F delivers a whopping 600 watts max (60 watts x 4 or 150 watts x 2 at 4 ohms 75 watts x 4 at 2 ohms) plenty of juice to power your high-quality speakers.
4 channel power amplifier professional#
Digital 2channel X 2000w PA 1u Professional Class D Power Amplifier Module K20. Nowadays 4 channel AMPs are also prevalent. Without it, the speakers would not get enough output power to run properly.
Both have a power supply to increase the 12V battery voltage. QSC PLD 4.2 700 Watt 4 Channel Power Amplifier. The 4 channel amplifier is similar to the 2 channel amp but there are some differences. Commonly, the rear channels will be bridged to power a small subwoofer while the front channels are used.
These amplifiers are designed to power four door speakers, although the right & left channels can usually be bridged to offer a wide range of wiring options. Wired remote level controls can be configured to allow simple control for the end user. Behringer NX4-6000 4 Channel Power Amplifier. A 4-channel amplifier is the best way to power a complete set of new car speakers. The output level can be assigned to either the front panel potentiometers or to the onboard GUI. Behringer NX4-6000 6000W 4-channel Power Amplifier. All amplifier channels have an assortment of DSP tools including level controls, EQs, limiters, high & low pass filters, and delay to provide flexibility for a range of applications. All inputs can be mixed and routed to any of the four amplifier channels. The DPA404 comes standard with four balanced line inputs and an accessory slot for an optional DPA-DAC4 four-channel Dante™ receiver card or a DPA-AMIX (2) mic/line and (2) AUX input card, for a total of eight inputs. The DPA404 can be configured for a 70.7V/100V paging/background system on two channels and the other two channels can be used for 4Ω/8Ω foreground stereo applications. Many system designs require both low and high impedance amplification. However, the DPA404 can be configured in four-channel mode with either 4Ω or 8Ω load impedances for two stereo zones. The DPA404 can be used right out of the box in its factory default configuration as a traditional four-channel 70.7V commercial power amplifier requiring no programming, special set-up, or network connectivity. The PMX 4810 four-channel power amplifier from the Classic range of products is specially designed as a cost effective solution for todays competitive. The network enabled DPA404 is a DSP controlled four-channel amplifier that can be configured in three different amplification arrangements to meet a wide range of installation design requirements. The third generation of Emotivas XPA range of power amplifiers uses an ingenious modular design that allows owners to gradually increase the number of channels as they build their system.
There are no “end-of-tunnel” output transistors subject to greater warming and, consequently, possible premature failure.The AtlasIED DPA404 amplifier features a combination of flexibility, performance, and control to provide high value features for applications that require more than just great sound. The Emotiva XPA-11 Gen3 is an 11-channel power amplifier from a US manufacturer that specialises in building affordable high-end products. All output devices are mounted transverse to the airflow, so the cooling effect is uniform. Twin variable-speed fans respond to temperature sensors, forcing air over the Intercooler fins in a front-to-rear flow. To ensure efficient, uniform cooling, the ultra-efficient Intercooler® uses thousands of tiny copper cooling fins to increase exposure of the heat sink to the cooling air flow. Working together, this new generation of proprietary circuits produces more power from a smaller package while at the same time maintaining LAB GRUPPEN’s peerless reputation for sonic excellence.
4 channel power amplifier series#
Both are incorporated in all four FP+ Series amplifiers. To achieve the extreme power-to-size ratio in the FP+ Series, LAB GRUPPEN engineers refined and upgraded two proprietary technologies: the regulated switch-mode power supply (R.SMPS™) and the patented Class TD™ output stage.